電訊茶室's Archiver

角色 發表於 2014-8-21 07:16

RB951G-2HnD + Huawei 3G E261 modem变成流动WiFi router

[i=s] 本帖最後由 角色 於 2014-8-22 22:14 編輯 [/i]

因为RB951G-2HnD有一个标准的大头USB,然后把我的Huawei 3G E261 modem直接插入就可以,然后根据下面的帖子就可以把RB951G-2HnD变成流动WiFi router。

1) Before putting the USB 3G modem, we have[code][admin@MikroTik] > /system resource usb print
# DEVICE VENDOR                   NAME                   SPEED                  
0 1:1    Linux 3.3.5 ehci_hcd     RB400 EHCI             480 Mbps               
[admin@MikroTik] >
[/code]2) After have put the USB 3G modem, we have[code][admin@MikroTik] > /system resource usb print
# DEVICE VENDOR                   NAME                   SPEED                  
0 1:1    Linux 3.3.5 ehci_hcd     RB400 EHCI             480 Mbps               
1 1:5    HUAWEI Technology        HUAWEI Mobile          480 Mbps               
[admin@MikroTik] > [/code]There is an element called HUAWEI Technology is given.

3) There is a new interface created and called ppp-out1[code][admin@MikroTik] > /port print
Flags: I - inactive
#   DEVICE NAME                     CHANNELS USED-BY                   BAUD-RATE
0   1:5    usb1                            4 PPP <ppp-out1>            9600     
[admin@MikroTik] >
[/code]4) Add the following nat[code]
/ip firewall nat add chain=srcnat action=masquerade to-addresses=0.0.0.0 out-interface=ppp-out1
[/code]5. The following action may be needed if the above steps do not make your system work

enable ppp-out1 interface


Ref:
[url]http://www.telecom-cafe.com/forum/viewthread.php?tid=5162&extra=page%3D2&page=1[/url]


[attach]3326[/attach]

角色 發表於 2014-8-21 07:16

[i=s] 本帖最後由 角色 於 2014-8-21 09:07 編輯 [/i]

测试结果:DL:440kbps,UL:190kbps,虽然慢!但是起来方案可行。

[attach]3325[/attach]

角色 發表於 2014-8-21 07:16

备用帖子。

hklkf 發表於 2014-8-21 14:15

still waiting my new toys RB951G-2HnD cn shipping to hk

角色 發表於 2014-8-21 22:03

[b]回復 [url=http://www.telecom-cafe.com/forum/redirect.php?goto=findpost&pid=39149&ptid=6347]4#[/url] [i]hklkf[/i] [/b]

其实这个Router,主要是小地方用,如家里或者房间里,还有它的CPU也非常快,再加上RAM,那么可以加入更加多的rules。

hklkf 發表於 2014-8-22 10:18

use for home wifi+3G MODEM CONNECT INTERNET+SITE TO SITE VPN

角色 發表於 2014-8-22 10:23

[b]回復 [url=http://www.telecom-cafe.com/forum/redirect.php?goto=findpost&pid=39153&ptid=6347]6#[/url] [i]hklkf[/i] [/b]

What kind of modem that you are going to use and the data plan? 384kbps? or 1Mbps?

hklkf 發表於 2014-8-23 16:56

[attach]3329[/attach]

[attach]3330[/attach]


speedtest

[attach]3331[/attach]

角色 發表於 2014-8-23 18:56

哗噻!!!你的LET 4G modem真的超快!比起我用的384kbps快很多!:L

角色 發表於 2014-8-25 13:56

如果家里不是很大,地方又小,那么这个设备最适合不过!(最好的是hardware够强,再加上RouterOS更加厉害!!!)

mrandrewchan 發表於 2015-1-3 08:35

hklkf  C Hing,

我用Vodafone K3765 找不到 sim card ( K3765  已unlock, 在鴨記買的One2free $48 試用 ), 請問你的 E392u-12 配那張上網卡? 謝謝

yiucsw 發表於 2015-1-18 13:50

我刚加了一个旧的4Gmodem ZTE820D。要Power OFF Router才能在Resource 看到。你们的是不是一样?
4G 123/1010 有多快,能代替PCCW的6M吗?

角色 發表於 2015-1-18 14:25

Power Off Router?是什么已经,如果power off router,你怎样打开RB呢?

yiucsw 發表於 2015-1-18 14:28

Any 4G LTE modem that can work with Mikrotik, which we can brough from taobao?
i try to use ZTE 820D, the mikrotik can recognize the modem but seem the interface is not working properly.  in firewall nat, the status is "ppp-out1 is not ready."

yiucsw 發表於 2015-1-18 14:46

In System resource detail, 以下是详细的信息。Interface 是Running, LTE Interface是没有显示。

1 device="1:3" vendor="ZTE,Incorporated" name="ZTE LTE Technologies MSM"
   serial-number="MF820DPLUS111111" vendor-id="0x19d2" device-id="0x0167"
   speed="480 Mbps" ports=0 usb-version="2.00"

角色 發表於 2015-1-18 18:05

What are the results as per the instructions shown in the first post?

yiucsw 發表於 2015-1-18 21:53

是System/Reboot 不能认USB ZTE. 要Shutdown/PowerOff/PowerON才能认ZTE USB Modem。
问题是USB 能認,但Status是Running,但没有Traffic, 在LTE Scanner也看不见。IP firewall route 到PPP-Out 的Interface有IN 没有Out traffic.
所有问一下如何, 第一步,如何知道Modem能连接到Carrier?
Set Dial On demand, status 是 Wait For  Traffic.

yiucsw 發表於 2015-1-18 21:56

Step 1-3, Done。 Interface ppp-out Enable. 4) 是将IP route,Destination Port 到 [url]www.google.com[/url] 地址。
结果如图显示一样。 只是没有Traffic。

角色 發表於 2015-1-18 22:14

你说“如图显示一样”,是哪个图呢?因为你Gateway 1依然有gateway,你可以看吧Ether1的Gateway拿走,看看怎样?

角色 發表於 2015-1-18 22:16

我忘了说,你把Ether1 disabled后,traffic应该往USB Modem那一边走。

yiucsw 發表於 2015-1-19 02:57

我猜是Data Port/info port 没有Set 对。

Qnewbie 發表於 2015-1-19 03:22

Tools=>Traceroute:
[attach]3423[/attach]

My 3G-dongle is auth. with ppp(ppp-out1 as gateway).

yiucsw 發表於 2015-1-19 03:28

[b]回復 [url=http://www.telecom-cafe.com/forum/redirect.php?goto=findpost&pid=40284&ptid=6347]22#[/url] [i]Qnewbie[/i] [/b]
你的LTE modem 是那个Model?

hklkf 發表於 2015-1-21 23:19

smartone



[b]回復 [url=http://www.telecom-cafe.com/forum/redirect.php?goto=findpost&pid=40028&ptid=6347]11#[/url] [i]mrandrewchan[/i] [/b]

yiucsw 發表於 2015-1-23 11:26

终于有机会再试试ZTE MF820D, 在system Logging 加Async Log,ATDT command 没有反应。ppp-out1 inteface-info 没有办法Search modem, 记得Huntsman 是改Info/data Channel.
不知道如何找Info/Data port, Try and Error 找到Info/Data Port 2 有反应。

想问有没有简单的Command 能Show Info/Data Port的?

当Info channel/data 改到 2是,
[attach]3431[/attach]
ppp - interface - ppp-out1 - info.
[attach]3432[/attach]

还没有时间是SpeedTest。 要是知道如何找到Data Channel, Pls Tell me.

yiucsw 發表於 2015-1-24 14:45

想知道用Huntsman 的Speed会不会快点?
speedtest.net
[attach]3433[/attach]
OFCA test
[attach]3434[/attach]

角色 發表於 2015-1-24 15:54

你的USB Modem弄好了?

yiucsw 發表於 2015-1-24 17:41

[b]回復 [url=http://www.telecom-cafe.com/forum/redirect.php?goto=findpost&pid=40343&ptid=6347]27#[/url] [i]角色[/i] [/b]
主要问题是在PPP Advance 内 - Info/Data Channel 要set 2.
在NAT加你的IP route rule 便可以。

PPP 的interface 比较慢。不知道有没有其他方法。
要换华为的LTE Modem可以加天线。

角色 發表於 2015-1-24 18:22

不太明白你的“主要问题是在PPP Advance 内 - Info/Data Channel 要set 2. ”是指什么?

还有你现在的速度在26#所显示吗? 如果是,那么也不错。

yiucsw 發表於 2015-1-24 21:22

不幸运,不知道原因有不成的。

頁: [1] 2

Powered by Discuz! Archiver 7.2  © 2001-2009 Comsenz Inc.