Look interesting subject. I look at GSMopen.org, it is for asterisk 1.4 and 1.6 only. It seems to work with spandsp from the source code filenames,作者: 雯雯 時間: 2011-2-4 12:46
I have some success here after plugging in my old E169G USB 3G modem from 3HK
again (Attempt #1011)
-- [datacard0] Trying to connect on /dev/ttyUSB2...
-- [datacard0] Datacard has connected, initializing...
[Feb 7 16:46:09] WARNING[4513]: at_response.c:392 at_response_error: [datacard0] Error checking subscriber phone number
-- [datacard0] Datacard needs to be reinitialized. The SIM card is not ready yet
-- [datacard0] Error initializing Datacard
-- [datacard0] Datacard has disconnected
-- [datacard0] Trying to connect on /dev/ttyUSB2...
-- [datacard0] Datacard has connected, initializing...
-- [datacard0] Datacard initialized and ready作者: ckleea 時間: 2011-2-7 16:30
Further update
ns*CLI> datacard show device statistics datacard0
-------------- Statistics -------------
Device : datacard0
Queue tasks : 55
Queue commands : 76
Responses : 109
Bytes of readed responces : 1233
Bytes of wrote commands : 383
Bytes of readed audio : 0
Bytes of wrote audio : 0
Readed frames : 0
Readed short frames : 0
Wrote frames : 0
Wrote short frames : 0
Wrote silence frames : 0
Write buffer overflow bytes : 0
Write buffer overflow times : 0
Incoming calls : 0
Waiting calls : 0
Handled input calls : 0
Fails to PBX run : 0
Attempts to outgoing calls : 0
Answered outgoing calls : 0
Answered incoming calls : 0
Seconds of outgoing calls : 0
Seconds of incoming calls : 0
ACD for incoming calls : -1
ACD for outgoing calls : -1
ASR for incoming calls : -1
ASR for outgoing calls : -1作者: 雯雯 時間: 2011-2-7 16:46
The modem disappears for unknown reason.作者: ckleea 時間: 2011-2-7 17:05
A reboot return the device /dev/ttyUSB0, /dev/ttyUSB1, /dev/ttyUSB2作者: ckleea 時間: 2011-2-7 17:11
Some more postings
------------- Settings ------------
Device : datacard0
Audio : /dev/ttyUSB1
Data : /dev/ttyUSB2
IMEI :
IMSI :
Channel Language : en
Context : default
Exten : +1234567890
Group : 0
RX gain : 0
TX gain : 0
U2Diag : -1
Use CallingPres : Yes
Default CallingPres : Presentation Allowed, Passed Screen
Auto delete SMS : Yes
Disable SMS : No
Reset Datacard : Yes
SMS PDU : Yes
Call Waiting : auto
DTMF : relax
Minimal DTMF Gap : 45
Minimal DTMF Duration : 80
Minimal DTMF Interval : 200作者: ckleea 時間: 2011-2-7 17:44
Successful SMS can be sent from CLI. But not outgoing call, probably not voice enable. 作者: ckleea 時間: 2011-2-7 17:58
Updated. my E169G is already unlocked for SIM and Voice.
selection :
manufacturer - Huawei modems
model - Auto detect (recommended)
Found modem : E169G
Model : Huawei E169/E169G
IMEI :
Serial NR. :
Firmware : 11.314.09.50.00
Compile date / time : Apr 26 2008 12:04:28
Dashboard version : UTPS11.002.03.05.23_MAC11.201.04.02.156
Chipset : Qualcomm MSM6280
NAND Flash : samsung_k9f1208
Voice feature : enabled
SIM Lock status : unlocked
Wrong codes entered : 0 (unlock attempts left : 10)作者: ckleea 時間: 2011-2-7 18:56
試過唔同SIMS，都係做唔到outgoing call.
-- Accepting AUTHENTICATED call from 192.168.1xx.xxx:
> requested format = alaw,
> requested prefs = disabled,
> actual format = alaw,
> host prefs = disabled,
> priority = reqonly
-- Executing [xxxxxxxxxxx@DLPN_DP1:1] Dial("IAX2/6xxx-1202", "Datacard/g0/8529xxxxxxx") in new stack
[Feb 7 19:16:18] WARNING[10626]: channel.c:165 channel_request: [g0] Request to call on device which can not make call at this moment
[Feb 7 19:16:18] WARNING[10626]: app_dial.c:2039 dial_exec_full: Unable to create channel of type 'Datacard' (cause 44 - Requested channel not available)
== Everyone is busy/congested at this time (1:0/0/1)作者: 雯雯 時間: 2011-2-7 19:09
