ckleea

試下更改 /etc/hosts 如下

;203.80.89.135       s2hkbntel.net s21.hkbntel.net
203.80.89.139                s2hkbntel.net s22.hkbntel.net
;203.80.89.146        s2hkbntel.net s23.hkbntel.net
;203.80.89.150        s2hkbntel.net s24.hkbntel.net

記得行 service network restart

假定你用 Centos /Redhat linux

電腦超人

4個也不行...
這次是顯示
  == Using SIP RTP CoS mark 5
    -- Called XXXXXXXX@s2hkbntel
    -- No one is available to answer at this time (1:0/0/0)
    -- Executing [XXXXXXXX@internal:2] Hangup("SIP/6001-00000016", "") in new stack
  == Spawn extension (internal, XXXXXXXX, 2) exited non-zero on 'SIP/6001-00000016'

ckleea

Please reboot your server once. It happens to me many times recently. YH advised me to reboot. It will work again.

電腦超人

reboot後也是不行...
看來我要再找找是甚麼問題了...

ckleea

回復 49# 電腦超人

Also reboot your router and try to go into 2b web page to reset your setting.

It just happens again to me last night. It is back to normal.

ckleea

Yes, I confirm that it is back to normal.

Try this link to reset your 2b account

http://pa.2b.com.hk/login.jsp

電腦超人

試過都係唔得...

Router都做哂port forward...
尋日試過搵X-Lite都成功...

ckleea

回復 52# 電腦超人


你用x lite 註冊？
一般我上述的方法是 work，不過可能需要 timeout 一段時間。

bubblestar

電腦軟件不如硬件電話，始終要面對cache 問題。應該要想想辦法每隔一段時間自動清洗Cache 便好了。

電腦超人

回復  電腦超人


你用x lite 註冊？
一般我上述的方法是 work，不過可能需要 timeout 一段時間。 ...
ckleea 發表於 2011-1-19 08:18

我試過用X-Lite是OK的...
跟著在pa reset後才再在asterisk註冊...但還是不行...

都係出"No one is available to answer at this time"

ckleea

回復 55# 電腦超人

Do you have other device login at the same time? Multiple login will require on client to time out for quite some time before allow to use 2b again.

I have this experience before

電腦超人

回復  電腦超人

Do you have other device login at the same time? Multiple login will require on cli ...
ckleea 發表於 2011-1-19 13:09

應該冇架喎...
我係初初拎個a/c之後試過login到就已經冇用過個2b software...

而且我o係pa度reset過都唔得...

電腦超人

其實我在想...會否與我安裝時make sample有關...
因為不知道原有設定會否影響我所修改的...

以及看了會否和router(ClearOS)有關...

我也試過把設定在IP01的GUI介面設定...不過好像也是不行...

電腦超人

其實我在想...會否與我安裝時make sample有關...
因為不知道原有設定會否影響我所修改的...

以及看了會否和router(ClearOS)有關...

我也試過把設定在IP01的GUI介面設定...不過好像也是不行...

ckleea

回復 59# 電腦超人


    What have you done? Install asterisk 1.8.2? just save a copy of the new one and then recover the old conf files. Try again. There have been changes in the confi but not that many. For me, I just use my 1.6 config files directly on 1.8 asterisk. No change of any config files.